Freehand drawing in the form of
Although Freehand vector graphics software, but sometimes we need charts, tables and the like to show some regular data, can be chosen to Freehand drawing does not provide a direct form of tools, how do? We can copy or import in other software, such as llustrator. Many people may not have ah, again relying on the "other" is not as to the reality of their own DIY, here are two ways to solve this problem.
Accurate method
This type of form is accurate, that the form of high, wide and how many rows, how many columns, the specific size of each cell can be determined.
First, a new document, open the ruler display (Ctrl + Alt + R), pulled out from the ruler on the auxiliary line, horizontal and vertical of the two, this four auxiliary lines "around the" general scope of the form shown in Fig.
View the status bar, select a suitable unit, such as Centimeter, and then double-click the secondary line, open the Settings window, above a total of four, pick any one, point Edit, fill in specific values. Smart friends must understand, we are here to actually set the table width and height, that is the difference between the two Horizontal table height, and of course between the width of Vertical, you need these four lines of a a set, here I set up the final form of high 6 cm wide, 13 cm. Point out ok.
In the toolbox select the rectangle drawing tool, supporting line from the upper left to lower right corner of the intersection began to drag, until the secondary line attached to four edges into red and then release the mouse, the results shown in Figure.
Now select the rectangle should also state, click Modify - Ungroup, make it into a path, hold down the Ctrl do not click on the blank space, cancel the selection rectangle, and then drag a selection box to live in the rectangular box (This step seems to be superfluous, one will be canceled for a further selection, in fact quite different, just select the entire rectangle, now select the node)
From the menu and choose Modify - Split, rectangular fell apart now, please separate the two lines up and down the left to select the node, as shown, press Ctrl + Shift + B to reconcile the operation, then the middle may have a lot of lines, crowded , and shows you step to reconcile the number of set very high, as long as we are here to form a trunk and a few you can open the Object panel, set the step in the Steps in the number of how much concrete is set, it depends on how many rows you need to form , 4, 5 lines on the fill, that is n-1 on it. Figure
Similarly, on the two vertical lines were also the same operation, the final set in the Steps in the number of columns, of course, have to cut a oh.
Table look is out now, all elected them, and then Group after group can build a unified movement.
[Next]
Rapid method
Although this method above accurate, but done too much trouble to do a rare form for more appropriate, more on the slow death. Relatively quickly following this approach, does not require very accurate for the case is a good choice.
Using the straight-line drawing tool, hold down the Shift shall draw vertical lines on the page can be longer appropriate, then the level of replication of a Figure. Lattice between the distance and the width of the form is almost the same time, press F8 to select them into a Symbol, and then press Tab to cancel all options.
Open the Stroke panel, select Brush, points at the top right button, choose New, the definition of brush in the window just in selected Symbol, because we do not turn over names, so it should be the default Graphic-01, and select the Spray method, other can not have changed the default settings, as shown.
The definition of a good brush, and first in the panel to select the brush, where the Brush-01, can now use, or painted line tool, hold down the Shift drag a horizontal line, the same, again and again out of a vertical line, the two intersect, as shown.
Would now like to intercept the form in which part of the new layer in the Layers Panel, dragged out a rectangular "box out" the form you want (first recognized Stroke is set to Basic), then the layer next to the hook to hide it, select All the lines, point cut command, then all the lines are gone, it does not matter. Followed earlier in the level of the rectangular plate shown, select it and press Ctrl + Shift + V, which came out under the table, as shown
If unhappy with the size you can zoom in, and operate as a general graphics.
Can see that the definition of a pen as long as we're OK, once the brush, since you can call at any time, very convenient. Now you can fill in the data.
Recommended links:
XviD to WMV
MKV to Zune
Dwwin exe dll initialization failed error repair
AVI to DivX
No comments:
Post a Comment